HQD Glow Air 70K Not Working? Here’s How to Fix It

• Khan Afridi

The HQD Glow Air 70K is a high-capacity prefilled pod kit designed for vapers who want long life, strong flavour and simple use without refills or coil changes. With up to 70,000 puffs, an 850mAh rechargeable battery, dual mesh coils, USB-C charging, a smart LED/OLED display, and a dual-flavour pod system, it sits between a disposable and a full pod kit.

But even strong devices like this can have problems. Many users search for “HQD Glow Air 70K not working”, “HQD Glow Air 70K not hitting” or “HQD Glow Air 70K not charging” when they face issues such as no vapour, burnt taste, leaking or flashing lights.

This guide is written for adult vapers who use the HQD Glow Air 70K and want clear, simple help. Below, you will find the 10 most common problems, why they happen, and step-by-step troubleshooting so you can get your device working again or know when it is time to replace it.

Quick Checklist Before You Start

Before diving into deep fixes, run through this quick checklist. Many “HQD Glow Air 70K not working” problems are solved here:

  • Check battery level on the LED or OLED display if your version has one.

  • Ensure the pod is properly inserted and fully clicked in.

  • Remove any stickers, seals or airflow plugs from a brand-new pod.

  • Check for visible leaks, cracks or damage on the pod and around the pod bay.

  • Confirm you are using original HQD pods, such as HQD Glow Air 35K-compatible pods, not random third-party pods.

If the device still misbehaves after this checklist, move on to the detailed sections below.

1. HQD Glow Air 70K Not Firing (No Vapour on Inhale)

When your HQD Glow Air 70K is not hitting at all, it usually means the device cannot power the coil, the pod is not detected, or the airflow sensor is not triggering.

Why This Happens

  • Battery is very low or completely flat

  • Pod not fully seated or making poor contact

  • Pod is empty or coil is burnt out

  • Airflow sensor blocked by dust, lint or condensation

  • Internal device fault (board or sensor failure)

Step-by-Step Fix

  1. Check the Pod

    • Look at the pod’s e-liquid level.

    • Check for cracks or leaks.

    • Smell the mouthpiece. A strong burnt smell means the coil is dead.

  2. Remove and Reinsert the Pod

    • Pull the pod out of the device.

    • Wipe the gold contacts on the pod and inside the device with a dry tissue.

    • Push the pod back in until it feels snug and sits flush. A loose pod often causes no vapour.

  3. Recharge the Battery

    • Connect a USB-C cable to a good 1–2A wall adapter.

    • Check the LED/OLED display for a charging symbol or battery bar.

    • Leave it to charge until the battery is at a healthy level.

  4. Clear the Airflow

    • Wipe the mouthpiece and visible airflow holes.

    • If you suspect condensation, blow gently through the mouthpiece into a tissue.

  5. Try a New Pod

    • Insert a fresh HQD Glow Air pod.

    • If the new pod works instantly, the old one was empty, burnt or faulty.

When to Replace the Device

If there is still no vapour, no proper LED activity, and no charging response even with a fully working cable and a fresh pod, the device has likely suffered an internal fault. At that point, it is safer to replace your HQD Glow Air 70K.

2. HQD Glow Air 70K Not Charging

If your HQD Glow Air 70K will not charge, you cannot use the device at all, even if the pods are full.

Common Causes

  • Damaged or cheap USB-C cable

  • Weak or incompatible charger / plug

  • Dust, pocket lint or e-liquid inside the USB-C port

  • Over-discharged or aged 850mAh battery

  • Device is too hot to accept a charge

How to Fix It

  1. Test the Charging Cable

    • Try a different USB-C cable that works with another device.

    • Loose or worn cables are a very common cause of charging problems.

  2. Clean the Charging Port

    • Use a dry cotton bud to gently clean the port.

    • Remove any fluff, dust or residue. Do not use water or metal tools.

  3. Confirm LED Charging Signal

    • Plug it in and look for a battery icon, charging bar or a pulsing light.

    • If you see nothing, test with another cable and plug.

  4. Try a Different Power Source

    • Use a proper 1–2A wall adapter instead of TV USB ports or very old phone chargers.

  5. Let the Device Cool Down

    • If the body feels warm or hot, unplug it.

    • Let it cool on a safe surface and then try charging again.

When to Replace the Device

If you still see no charging icon, no LED response, and no progress after all the above steps, the charging circuit or battery is likely damaged. In that case, it is time to replace the HQD Glow Air 70K rather than forcing it.

3. Weak Vapour or Muted Flavour

Sometimes your HQD Glow Air 70K still fires, but vapour feels thin and flavour is weak. This usually means the pod, coil, battery or airflow is not in ideal condition.

Why Vapour Feels Weak

  • Low battery voltage

  • Worn dual mesh coil in the pod

  • Pod almost empty

  • Airflow partially blocked by dust or condensation

  • Chain vaping has overheated the coil

  • Inhaling too softly or too aggressively

Step-by-Step Fix

  1. Check Pod Liquid Levels

    • Look at the pod. If it is very low, performance will drop.

  2. Replace Worn-Out Pod

    • The dual mesh coil inside slowly wears down.

    • A fresh pod usually restores full flavour and vapour.

  3. Slow Down Puffing

    • Take slower, steady mouth-to-lung puffs.

    • Avoid long chains of puffs with no breaks.

  4. Fully Recharge the Battery

    • Weak battery = weak vapour.

    • Charge the device to full and compare performance.

  5. Clear the Airflow

    • Clean the mouthpiece and airflow slots.

    • Remove any visible build-up or moisture.

When to Replace the Pod

If vapour and flavour remain muted even after charging and cleaning, the pod is likely worn out and should be replaced.

4. Burnt or Harsh Taste

A burnt HQD Glow Air 70K is a sign that the coil has overheated or run dry.

What Causes Burnt Hits

  • E-liquid level is very low or finished

  • Dual mesh coil is burnt from use

  • Puffing very hard or very often

  • Pod used far beyond its realistic life

How to Fix / Prevent Burnt Taste

  1. Check E-Liquid Level

    • If the pod looks almost empty, stop using it.

    • Vaping on a dry pod burns the cotton permanently.

  2. Replace Burnt Pod

    • Once you taste burning, that coil is done.

    • Burnt cotton does not “heal” – it needs a new pod.

  3. Slow Down Puffing

    • Take shorter puffs.

    • Leave a few seconds between each puff so the wick re-saturates.

  4. Switch Flavours Slowly

    • If your pod has dual flavours, avoid switching back and forth rapidly.

    • Give the wick a few puffs to adjust each time you change flavour.

  5. Recharge the Battery

    • Weak, unstable power can feel harsh.

    • A full charge makes heating more consistent.

When to Replace Pod

If burnt taste persists after one or two test puffs on a freshly charged device, the pod is finished and should be replaced.

5. Leaking or Gurgling

Light condensation is normal, but heavy leaking or loud gurgling in the HQD Glow Air 70K indicates a problem.

Why the Pod Leaks

  • Condensation build-up in chimney or mouthpiece

  • Over-inhaling and flooding the coil

  • Heat or pressure changes (hot cars, tight pockets, travel)

  • Faulty or damaged pod seal

Easy Fixes

  1. Remove Pod and Clean Everything

    • Wipe pod base, mouthpiece, contacts and pod bay with a dry tissue.

  2. Insert Pod Securely

    • Make sure it is aligned and clicked in properly.

  3. Adjust Your Puffing Technique

    • Use gentler, steady pulls instead of sharp and heavy inhales.

  4. Store Device Upright

    • Keep the device standing when possible.

    • Avoid hot environments which thin the liquid and encourage leaks.

  5. Replace the Pod

    • If the same pod leaks heavily or gurgles constantly, swap it for a new one.

When to Worry

If you see e-liquid inside the charging port, around the screen, or deep inside the body, it is safer to retire that device and move to a new one.

6. Pod Not Detected / LED Error Flashes

If your HQD Glow Air 70K is blinking and not hitting, the device is usually telling you something is wrong with the pod, connection, battery or coil.

Common Reasons

  • Pod not fully clipped in

  • Wet or dirty contacts

  • Flooded coil acting like a short

  • Wrong or faulty pod

  • Internal chipset or sensor issue

What to Do

  1. Remove and Inspect the Pod

    • Look for damage, cracks or heavy leaking.

    • Make sure any stickers or plugs are removed.

  2. Dry and Clean the Contacts

    • Use a dry tissue to clean the gold contacts on the pod and inside the device.

  3. Reseat the Pod Until It Clicks

    • Insert it firmly so it sits straight and flush.

  4. Clear the Airflow / Deflood the Pod

    • If you hear gurgling, gently flick the pod into a tissue or blow through the mouthpiece.

  5. Recharge the Battery

    • Low battery can also cause flashing lights and misfires.

  6. Try a Fresh Pod

    • If a new pod works, the old one was likely faulty or flooded.

When to Replace the Device

If the LED error continues with multiple pods and a full battery, then the internal chip or sensor is likely damaged. It is time to replace the device.

7. Auto-Firing or Device Heating Up

Auto-firing is when the HQD Glow Air 70K activates on its own. This is a serious safety issue and must be handled carefully.

Causes

  • Stuck or over-sensitive auto-draw sensor

  • Liquid inside device causing short circuits

  • Internal chip or battery damage from impact or wear

Immediate Actions

  1. Remove the Pod Immediately

    • Break the connection so the coil cannot keep heating.

  2. Wipe and Inspect the Device

    • Check the pod bay and surrounding areas for e-liquid and dry them thoroughly.

  3. Allow the Device to Cool Down

    • Place it on a non-flammable surface and let it cool completely.

  4. Insert a Fresh Pod and Test Carefully

    • Once the device is cool and dry, you may test with a new pod.

    • If it only fires when you inhale, it might be safe to continue.

  5. If Problem Persists Without Pod, Replace the Device

    • If the device heats up or activates even with no pod installed, do not use or charge it again. Replace it.

8. Airflow Too Tight or Too Loose

The HQD Glow Air 70K is designed for smooth MTL draws, but sometimes the airflow can feel either too restricted or too open.

Why This Happens

  • Condensation or debris in air channels

  • Pod slightly misaligned

  • Small natural differences between pods

  • User expectations from other devices with different airflow

How to Improve Airflow

  1. Clean Mouthpiece and Airflow Holes

    • Wipe off any visible condensation or dust.

  2. Remove and Reinsert the Pod

    • Make sure it is fully seated and not skewed.

  3. Clear Condensation

    • Blow gently through the mouthpiece to remove internal moisture.

  4. Adjust Puffing Style

    • For tight airflow, try slower pulls.

    • For loose airflow, shorter and slightly firmer puffs may feel better.

  5. Try a New Pod

    • If one pod feels wrong from the start, test another pod of the same type.

When to Replace the Device

If airflow is strange or inconsistent across several pods, the internal airflow design may be damaged. That is a sign you should replace the device.

9. Battery Draining Faster Than Expected

You might notice your HQD Glow Air 70K battery does not last as long as it did when new.

Normal vs Not Normal

  • Puff count always depends on puff length and frequency.

  • Heavy vapers will drain the 850mAh battery faster.

  • Over time, all lithium batteries lose capacity.

Tips to Maximise Battery Life

  1. Avoid Chain Vaping

    • Give the device small rests between puffs.

  2. Fully Charge Before Use

    • Let the battery reach full before long sessions.

  3. Use Normal Mode

    • If your variant supports extra performance modes, stay in normal mode for better life.

  4. Keep at Room Temperature

    • Avoid very hot or very cold environments.

  5. Check for Pod Issues

    • Faulty pods can make the device work too hard.

  6. Replace Device if Battery Is Worn Out

    • If you vape lightly but still need to recharge constantly, the internal battery is likely worn and the device should be replaced.

10. Flavour Tastes Mixed After Switching (Dual-Flavour Pods)

The HQD Glow Air 70K uses a dual-flavour / multi-flavour system on some versions, letting you switch flavours with a slider or switch.

Why This Happens

  • Two flavours share the same dual mesh coil and chimney

  • The wick holds the previous flavour

  • Rapid switching between flavours

How to Get Cleaner Flavour

  1. Fully Switch the Flavour Selector

    • Make sure the slider or switch is fully over to one flavour, not in the middle.

  2. Take Several Puffs After Switching

    • Expect 3–6 puffs before the new flavour fully comes through.

  3. Clear the Airflow

    • Blow lightly through the mouthpiece to help push out leftover vapour.

  4. Use Fresh Pods for Best Flavour

    • Old pods will always taste a bit mixed or dull compared to new ones.

  5. Manage Expectations

    • Some slight flavour overlap is normal with dual-flavour pod systems.

When to Replace the Pod

If flavour stays muddy, dull or slightly burnt even after several puffs and cleaning, the pod has reached its limit and should be replaced.

When to Replace Your HQD Glow Air 70K Completely

You should consider replacing the HQD Glow Air 70K device if:

  • There is no LED or charging sign even with good cables and adapters.

  • The device has severe leaking inside or liquid has entered the charging port.

  • It has auto-fired or overheated more than once.

  • Multiple pods are not detected or always trigger error lights.

  • The device has been dropped in water or suffered heavy impact.

At that point it is safer to buy a new HQD Glow Air 70K kit or move to another rechargeable prefilled pod kit from your shop’s range.

Newer post
Older post
Back to blog