Angel 20K Puffs Not Working? 10 Common Problems & Easy Fixes

Why Your Angel 20K Might Stop Working

Your Angel 20K is a dual-flavour, reusable big-puff pod kit designed for easy and smooth vaping. It uses prefilled pods, mesh coils, and an 850mAh rechargeable battery, which normally work together to give strong flavour and steady vapour. But like any vape device, small issues can appear over time — such as no vapour on inhale, weak vapour, burnt taste, pod not detected, or not charging.

The good news is that most Angel 20K not working problems are simple and can be fixed at home in just a few minutes. Many issues come from loose pods, low battery, blocked airflow, or small bits of condensation — nothing serious.

Quick Checklist Before You Start

Before jumping into the detailed fixes, run through this simple checklist. It solves more than half of all Angel 20K pod kit problems:

• Check the battery level on the LCD screen

• Make sure the pod is inserted properly and clicked into place

• Remove all stickers, rubber plugs and airflow seals from new pods

• Look for leaks, cracks or damage on the pod and device

• Use only original Angel 20K pods/refill packs for best performance

• Wipe the contacts (both pod and device) with a tissue or cotton bud to clear condensation or dust

Once you complete this quick check, most Angel 20K not firing or not hitting issues start working again. If not, don’t worry the next sections will guide you step-by-step through each problem.

1. Angel 20K Not Firing (No Vapour on Inhale)

Why This Happens

If your Angel 20K is not firing and there’s no vapour when you inhale, it usually comes down to a few simple causes:

• Flat battery – the device doesn’t have enough power to heat the coil

• Loose pod or poor contact – the pod isn’t sitting properly in the device

• Airflow sensor not activating – the sensor can’t detect your inhale

• Pod coil burnt out or dead – the pod has reached the end of its life

These are very common issues in MTL pod kits, especially reusable devices like the Angel 20K.

Step-by-Step Fix

1. Check the LCD screen
   Make sure the battery isn’t at 0%. If it’s low or empty, recharge the device.

2. Recharge fully
   Plug your Angel 20K into a USB-C cable and use a standard low-watt charger. Wait until the battery is clearly charging.

3. Remove and reinsert the pod

   • Take out the dual-flavour pod section

   • Wipe the base and device contacts

   • Insert the pod again until it clicks into place

4. Clean the contacts
   Use a dry tissue or cotton bud to remove any dust or condensation.

5. Try the other pod side
   Switch to the second flavour pod.
   If one works and the other doesn’t → the coil on that pod is likely dead.

6. Try a brand-new pod
   If neither side fires, the pod pack may be finished. Fresh pods often fix the issue instantly.

When to accept the pod/coil is done:
If the pod still won’t fire even after cleaning, charging, and reseating, the coil is likely burnt out or fully dead — replace it with a new Angel 20K pod pack.

2. Angel 20K Not Charging

Common Causes

If your Angel 20K won’t charge, the issue is usually one of these:

• Using the wrong charger, especially high-power “fast chargers”

• Dirty or blocked USB-C port with pocket fluff or dust

• Damaged charging cable or loose connection

• Internal battery fault after long-term use or damage

All of these are common problems with rechargeable vape devices.

How to Fix It

1. Try a different cable and plug
   Use another USB-C cable and a low-watt plug (5V/1A). Avoid fast-charging bricks.

2. Inspect and clean the charging port
   Look inside the USB-C port for dirt or fluff. Gently blow or tap to remove debris.
   Never poke metal objects inside.

3. Leave it to charge properly
   Give the device at least 30–60 minutes, even if the screen doesn’t show charging immediately.

4. Check for overheating
   If the device gets very hot while charging, unplug it right away.
   This is a sign the internal battery may be failing.

When to replace the device:
If it still won’t charge after trying different cables and cleaning the port, the battery is likely worn out or faulty — replacing the device is the safest option.

---

3. Weak Vapour or Muted Flavour

Why Vapour Feels Weak

If your Angel 20K is giving weak vapour or muted flavour, it usually means:

• Low battery output – vapour is weaker when the battery is nearly empty

• Coil is near the end of its life – flavour naturally fades over time

• Pod not fully saturated – especially after installing new pods

• Tight MTL draw – some users expect DL-style clouds, but this is an MTL pod kit

These are normal behaviours in mesh-coil prefilled pod systems.

Step-by-Step Fix

1. Charge the device fully
   Weak vapour is very common on a low battery.

2. Flip the device upside down
   Hold it upside down for 5–10 seconds. This helps fresh e-liquid soak into the mesh coil.

3. Take short breaks between puffs
   Chain-vaping can starve the coil of e-liquid and cause weak hits.

4. Replace the pod if flavour is still dull
   If the vapour or flavour remains weak after charging and flipping, the pod may be worn out — a new pod usually fixes it immediately.

4. Burnt or Harsh Taste

What Causes Burnt Hits

If your Angel 20K tastes burnt or harsh, the coil inside the pod is struggling to stay saturated. The most common reasons are:

• Chain-vaping too quickly – the coil doesn’t get enough time to re-soak with e-liquid

• Low liquid in the 2ml section – the coil dries out even if the refill container still has liquid

• Coil never primed properly – new pods need a moment to fully soak

• Coil simply worn out – after long use, the mesh coil naturally burns out

These issues are very common with mesh coil prefilled pods, especially high-strength nic salt pods.

How to Fix / Prevent Burnt Taste

1. Rest the device between puffs
   Give the coil a few seconds to soak before taking the next pull.

2. Prime a new pod properly
   When installing a new Angel 20K pod, flip the device upside down for 5–10 seconds to help liquid reach the coil faster.

3. Stop vaping when flavour drops
   If the flavour is fading or the pod feels “dry”, stop using it until it re-saturates.

4. Replace the pod
   Once a pod tastes burnt, it almost never recovers.
   The only real fix is to use a fresh Angel 20K pod pack.

5. Leaking or Gurgling

Why the Pod Leaks

If your Angel 20K pod is leaking or gurgling, it’s usually because too much liquid or condensation has built up around the coil or mouthpiece. Common causes:

• Over-saturation of the coil – especially after long rests or warm conditions

• Condensation build-up in the chimney or mouthpiece

• Pod stored on its side or in a hot car – heat pushes liquid into the coil

• Small cracks or worn-out seals on the pod

These issues happen with many prefilled pod systems, not just the Angel 20K.

Easy Fixes

1. Remove the pod and wipe everything
   Clean the device, pod base, pod bay and mouthpiece with a tissue.

2. Clear the chimney
   Hold a tissue at the base and give a short, sharp blow through the mouthpiece to push out excess liquid.

3. Keep the device upright
   Storing your vape upright helps prevent flooding and leaks.

4. Replace the pod if leaking continues
   If the pod has cracks or keeps leaking no matter what, switch to a new one.

6. Pod Not Detected / LED Error Flashes

Common Reasons

If your Angel 20K shows LED flashes or the pod isn’t detected, it’s usually related to connection problems. Typical causes:

• Pod not fully clicked in – the device can’t read it

• E-liquid or debris on the contacts

• Using non-compatible pods – only Angel 20K pods will work

• Internal connection fault inside the device

These problems are common with pod-based vapes when condensation builds up.

What to Do

1. Remove and reinsert the pod
   Make sure it clicks securely into place.

2. Clean the contacts
   Use a dry tissue or cotton bud to wipe the metal contacts on both the pod and the device.

3. Try another genuine Angel 20K pod
   If one pod fails but another works, the first pod is faulty.

4. If multiple pods fail
   The issue is likely inside the device.
   In this case, it’s best to replace your Angel 20K, as internal faults usually can’t be fixed at home.

7. Auto-Firing or Device Heating Up

Causes

Auto-firing (device activating by itself) is serious. Likely causes:

• Stuck airflow sensor

• Condensation or juice in the sensor channel

• Internal short or liquid inside the device

Immediate Actions

1. Stop using the Angel 20K immediately.
   Do not inhale while it’s auto-firing.

2. Remove the pod and unplug from any charger.
   Separate the pod from the device so it can’t keep producing vapour.

3. Let the device cool down.
   Place it on a non-flammable surface and allow it to fully cool.

4. Check for visible damage or liquid.
   If you see liquid inside the pod bay or device, gently wipe what you can reach.

5. Do not continue using a device that still auto-fires.
   If the Angel 20K tries to fire with no pod attached, or continues acting strangely, safely dispose of it and get a replacement. Auto-firing is not worth “testing” repeatedly.

8. Airflow Too Tight or Too Loose

Why This Happens

The Angel 20K is built for MTL (mouth-to-lung) vaping, similar to a cigarette draw. 

If the draw feels wrong, it can be:

• Condensation or e-liquid restricting airflow

• Slight variation between pods

• User expecting direct-lung style from an MTL device

How to Improve Airflow

1. Clean the mouthpiece.
   Remove the mouthpiece, wipe inside it with a tissue to clear condensation.

2. Clear the chimney.
   Do a gentle blow through the mouthpiece into a tissue at the bottom to push out excess liquid.

3. Try the other pod side.
   Sometimes one flavour side feels slightly tighter or looser – switching can improve the experience.

4. Replace the pod if it feels “choked”.
   If the draw is extremely tight or whistle-y after cleaning, that pod may be defective.

5. Remember: it’s an MTL kit.
   If you want big direct-lung clouds, this pod kit is not designed for that style, so the draw will always be on the tighter side.

9. Battery Draining Faster Than Expected

Normal vs Not Normal

The Angel 20K uses an 850mAh built-in battery, designed to last most vapers a day with typical MTL use. 

It’s normal for it to drain faster if:

• You’re vaping very frequently

• You take long, deep pulls

• You’re using it in cold weather

It may be not normal if:

• Battery drops from high to very low suddenly

• It won’t hold charge for more than an hour even with light use

Tips to Maximise Battery Life

• Top up charge instead of running it to 0% constantly.

• Avoid extreme temperatures – don’t leave it in a very hot car or freezing environment.

• Use sensible chargers – standard wall plugs rather than aggressive fast-charging bricks.

• If battery life rapidly gets worse after a few months, it’s likely the cell has reached its natural end – time to replace the device.

10. Flavour Tastes Mixed After Switching (Dual-Flavour Pods)

One of the biggest selling points of the Angel 20K is the 2-in-1 dual-flavour system. But sometimes when you switch flavours, you may feel they’re blending together.

Why This Happens

• Residual vapour from the previous flavour in your mouth and lungs

• Condensation in the mouthpiece holding traces of the last flavour

• Vaper’s tongue – your taste buds getting tired of strong flavours

How to Get Cleaner Flavour

1. Purge a few puffs.
   After switching flavour sides, take 2–3 short puffs and blow them out, without fully inhaling. This helps clear leftover vapour.

2. Clean the mouthpiece.
   Wipe inside the mouthpiece so old condensation doesn’t mingle flavours.

3. Drink water or neutral drink.
   Rinse your mouth or sip water to “reset” your taste buds.

4. Check you’ve actually switched pods.
   Make sure you’ve fully rotated the mouthpiece so you’re definitely on the other pod.

5. Replace pods if flavours are always muddy.
   Old pods can lose their sharp flavour – fresh pods give much cleaner separation.

When to Replace Your Angel 20K Completely

Troubleshooting can sort out most Angel 20K not working problems, but there are times when replacement is the safest and smartest option.

Replacement Checklist

Replace the whole device if:

• It won’t charge or turn on with any cable or plug

• It auto-fires or gets excessively hot, even with no pod attached

• It has deep cracks, warping, or obvious damage

• Multiple genuine Angel 20K pods aren’t detected

• Battery life has become extremely poor and drops rapidly

A fresh device protects you from electrical risk and also gives your customers the best possible experience with their pods and flavours

---

FAQs

1. Is the Angel 20K rechargeable?

Yes. The Angel 20K includes an 850mAh rechargeable battery with USB-C charging and an LCD battery display so you can see charge levels at a glance.

2. Can I use any pods with the Angel 20K?

No. You should only use official Angel 20K prefilled pods and refill containers. Third-party pods may not fit properly and can cause leaks, detection errors or safety issues.

3. Is it safe if my Angel 20K gets warm when charging?

A slight warmth while charging is normal. If the device becomes very hot, swells, smells strange or shows error behaviour, unplug it immediately and stop using it.

4. How long does an Angel 20K pod last?

It depends on how heavily you vape, but each pod is designed to provide a large puff count from its 2ml + 10ml setup. Once the flavour drops, tastes burnt, or vapour is weak even after charging, it’s time to swap to a fresh pod.

5. Can I keep using the device if it tastes burnt?

You can, but you shouldn’t. Burnt taste means the coil is damaged. It’s better for your throat and your overall experience to replace the pod immediately.